It is currently 29 Mar 2024, 10:03

Multico Model K1 Morticer Restoration

Here's the place to talk about all your table saws, bandsaws, routers and dust extractors. In fact anything that makes noise and uses electrickery.

Multico Model K1 Morticer Restoration

Postby Trevanion » 27 Sep 2020, 20:16

March the 4th, I bought this sorry looking thing for £60. Had been stored in a cow shed for god knows how long and god knows how much longer before that it was actually used. I figured for the money even if it was totally knackered I could at least turn the legs into a nice (and absurdly heavy) bar stool or something.

Image

I picked it up late at night in a cowshed with no lighting so I didn't really get a good look at it until I got home.

Image
Image
Image

So... obviously she's a little rough around the edges but it does actually fire up despite the very dubious at best cabling and archaic switchgear.

Image

Multico Model K, Serial number 524. I really do like these Multico badges, they clean up nicely too.

Image
Image
Image

I know some will scream sacrilege but I'll swap this switchgear out for something a bit more modern, it is a nice switch though and probably better built than most anything that could be bought today!

Image

A 3/4hp single-phase Hoover motor, there was a bit of speculation about the "3063" stamped on the tag meaning that it was made in the 30th week of 1963 but I wouldn't know.

Image

Inside the top of the motor, the wires on the infeed power and capacitor have completely perished which isn't too much of a big deal since I'll be replacing these. Very fortunately, the wires from inside the motor itself are in very good condition comparatively, I really wouldn't even want to start trying to replace those.

Image

Pulled the chisel and auger out of the head, definitely has seen better days...

Image

The bed had a rather thick layer of rust and grime! I started to attack it with a block of wood with an 80 grit piece of sandpaper wrapped around it to try and get back to decent metal. Rusted cast-iron always looks worse than it actually is.

Image

Image

Revealing the planed/shaped finish on the bed.

Image

Seems someone followed the old engineer's pillar drill rule of thumb of "keep going until you see iron shavings" on this poor morticer.

Image

Considering how bad it looked initially it cleaned up very nicely.

Image

Everything is caked in this sorta baked-on greasy dirt, fortunately though it seems the oil or grease has kept the bed ways looking pretty good even after however many years in the dirt.

Image

Mostly stripped down!

Image

Oh dear, taking the column off has revealed this crack on the bottom on the casting, it looks a lot worse in the photo than it actually is. I don't really see how this could've happened unless the counterweight has come loose at some point and hit the bottom very hard as in theory this part of the casting shouldn't have any load if it was ever tipped over as the hole only locates the column onto the base casting and it's bolted on the four corners pretty solidly. I'll leave it be rather than trying to repair it as it won't actually affect anything either way since as I said, it only locates the column initially and is then bolted on the four corners.
Image

Image

With the machine all in bits I got to working on said bits and making good what needed making good, the first start was the capacitor which whilst it did work the cable had become seriously perished and was crumbling away in my hands so I plopped a new one on order and thought nothing of it until it arrived and I discovered to my stupidity for not checking that it was much larger than the original one so it didn't fit in the original capacitor holder.

Image

So I did what any reasonable human being would do and spent a day making a new capacitor box of course!

Image

Image

It's quite a bit larger than the old box but it doesn't look totally daft on the motor.

Image

Image

Made a new back cover plate to hide the counterweight since the original one was missing, I also re-tapped the holes in the back for M6.

Image

Image

Image

Image

The bed clamping lever had seen much better days, rather than trying to bodge the existing one I just made a new one. Cut some 5/16" BSW threads, drilled a hole for a lever bar and threaded it M8, made a little bar and put a small 16mm ball on the end. You can see in the photos that the gib itself has snapped at some point, possibly from overtightening, I'll sort this out while I'm at it.

Image

Image

I wasn't really sure how to go about repairing the gib initially, I didn't really fancy brazing it so I came up with this idea. Three pins accurately put into the crack so that the parts come together perfectly and then epoxied them together, I reckon the repair will be good enough for the task.

Image

Image

Image

Image

Image

Image

Image

Image

Image

The original handwheels needed attention, the one for the lever handle was missing completely and the one for the bed clamp was brittle and on its way out. It's quite common for these to be missing or in poor condition so I assume the plastic they used was pretty rubbish or just didn't age well. I decided to push the boat out and make some scalloped wheels from some 3" aluminium bar, they're quite crude really as they're mostly shaped by hand but it's more function over form in this case. The lever handle used a left-handed 1/2" BSF thread which was a fun time finding a tap to match!

Image

Image

Image

The original part to hold the bed clamp to the bed had seen better days and used a nut, I fancied making a replacement that used a locking lever instead.

Image

Image

Cleaned the outside of the handwheels for the beds, these had some kind of dipped plastic coat covering them originally which looked pretty terrible so I pulled what remained off and turned the outer diameters concentric with the bores since they were pretty far out and then polished them.

Image

Image

Skimmed the collet holder and polished it up since the chrome/nickel plating they used had gone pretty nasty. I also took the lever bar and drilled and tapped each end for m10, shoved a bit of stud in the ends to accept the new 32mm balls.

Image

Image

Image

I made a bracket to fit the new switchgear to the side of the machine so that it's facing outwards towards the operator rather than just bolting it directly to the side of the machine.


Image

Image

Attacking everything with a wire wheel to prep them for paint, careful not to touch the machined surfaces.

Image

When cleaning up the castings I noticed these two screws, except they're not screws but actually a part of the casting. I can only guess they were holding the wooden pattern together when they were doing the moulds, pretty neat.

Image

Image

Image

Image

Image

White paint on, even the counterweight!

Image

Image

Image

Image

Blue on!

Image

Image

Lettering, a steady hand required, do not have!

Image

I put the motor back together, I didn't bother replacing the bearings as the ones inside were in really condition since they had been heavily greased but not over-used plus they were Hoffman bearings in the motor which are hard to match quality-wise.

Image

Now to put everything back together, I bought new hardware that wasn't overly cheap but will make the job look that much nicer. Black washers for extra fancy points!

Image

The finished article, something I neglected to mention before is that I put a locking lever handle in the head for holding in the chisels rather than the bolt that was there before. I've used SY control cable for the flex as I think it looks nice more than anything.

Image

Image

Image

Image

Image

Image

Image

Image

Image


Image

Image

I hope you enjoyed reading and haven't minded the travesty and chaos going on in the background, I've enjoyed doing it up :)
Image
User avatar
Trevanion
Old Oak
 
Posts: 2162
Joined: 27 Apr 2019, 19:04
Location: Pembrokeshire
Name:

Re: Multico Model K1 Morticer Restoration

Postby Malc2098 » 27 Sep 2020, 20:49

Nice.

I do like a shiny handwheel!
Malcolm
User avatar
Malc2098
Sequoia
 
Posts: 7209
Joined: 03 Jul 2016, 11:10
Location: Tiverton
Name: Malcolm

Re: Multico Model K1 Morticer Restoration

Postby MJ80 » 27 Sep 2020, 20:56

I used to have one of those, but what you have done is stunning.
MJ80
Sapling
 
Posts: 323
Joined: 13 Sep 2016, 19:21
Name:

Re: Multico Model K1 Morticer Restoration

Postby DaveL » 27 Sep 2020, 22:03

Now that is very nice, reminds me that the Draper machine I have really is a toy!
Regards,
Dave
My tool kit is almost complete, only a few more to get.
User avatar
DaveL
Old Oak
 
Posts: 1918
Joined: 21 Jul 2014, 21:07
Location: Sudbury, Suffolk
Name: Dave

Re: Multico Model K1 Morticer Restoration

Postby Andyp » 28 Sep 2020, 07:13

Good as, or most likely, better than new. I’ve enjoyed readings both of your restorations. Are these for personal use or do you sell them on?
I don’t have the skills nor the will to take on something like that but I am so pleased that you and a few others around here continue to do so and take the time to detail the process.
I do not think therefore I do not am.

cheers
Andy
User avatar
Andyp
Petrified Pine
 
Posts: 11721
Joined: 22 Jul 2014, 07:05
Location: 14860 Normandy, France
Name: Andy

Re: Multico Model K1 Morticer Restoration

Postby Trevanion » 28 Sep 2020, 07:46

Andyp wrote:I’ve enjoyed readings both of your restorations. Are these for personal use or do you sell them on?


Thanks, they're just copy & pasted over from the other place but I thought you guys here might like them. So far I've kept the two machines but I'd be tempted to sell the morticer just for more space as I've already got a nice Sedgwick (Which is due some TLC too at some point)
Image
User avatar
Trevanion
Old Oak
 
Posts: 2162
Joined: 27 Apr 2019, 19:04
Location: Pembrokeshire
Name:

Re: Multico Model K1 Morticer Restoration

Postby Robert » 28 Sep 2020, 10:08

As someone that never visits that other place I've enjoyed reading through this thread.

Thanks for posting it and if you have more don't be shy :)

Oh and lovely job on the restoration of course.
Robert
Old Oak
 
Posts: 2490
Joined: 21 Jul 2014, 19:31
Location: Woodford Green
Name: Robert


Return to Machines & Power Toolery

Who is online

Users browsing this forum: No registered users and 9 guests